Private: Chapter Eight

Effusion and Diffusion of Gases (8.4)

Effusion and Diffusion of Gases

By the end of this section, you will be able to:

  • Define and explain effusion and diffusion
  • State Graham’s law and use it to compute relevant gas properties

If you have ever been in a room when a piping hot pizza was delivered, you have been made aware of the fact that gaseous molecules can quickly spread throughout a room, as evidenced by the pleasant aroma that soon reaches your nose. Although gaseous molecules travel at tremendous speeds (hundreds of meters per second), they collide with other gaseous molecules and travel in many different directions before reaching the desired target. At room temperature, a gaseous molecule will experience billions of collisions per second. The mean free path is the average distance a molecule travels between collisions. The mean free path increases with decreasing pressure; in general, the mean free path for a gaseous molecule will be hundreds of times the diameter of the molecule

In general, we know that when a sample of gas is introduced to one part of a closed container, its molecules very quickly disperse throughout the container; this process by which molecules disperse in space in response to differences in concentration is called diffusion (shown in Figure 8.31). The gaseous atoms or molecules are, of course, unaware of any concentration gradient, they simply move randomly—regions of higher concentration have more particles than regions of lower concentrations, and so a net movement of species from high to low concentration areas takes place. In a closed environment, diffusion will ultimately result in equal concentrations of gas throughout, as depicted in Figure 8.31. The gaseous atoms and molecules continue to move, but since their concentrations are the same in both bulbs, the rates of transfer between the bulbs are equal (no net transfer of molecules occurs).

In this figure, three pairs of gas filled spheres or vessels are shown connected with a stopcock between them. In a, the figure is labeled, “Stopcock closed.” Above, the left sphere is labeled, “H subscript 2.” It contains approximately 30 small, white, evenly distributed circles. The sphere to its right is labeled, “O subscript 2.” It contains approximately 30 small red evenly distributed circles. In b, the figure is labeled, “Stopcock open.” The stopcock valve handle is now parallel to the tube connecting the two spheres. On the left, approximately 9 small, white circles and 4 small, red circles are present, with the red spheres appearing slightly closer to the stopcock. On the right side, approximately 25 small, red spheres and 21 small, white spheres are present, with the concentration of white spheres slightly greater near the stopcock. In c, the figure is labeled “Some time after Stopcock open.” In this situation, the red and white spheres appear evenly mixed and uniformly distributed throughout both spheres.
Figure 8.31 (a) Two gases, H2 and O2, are initially separated. (b) When the stopcock is opened, they mix together. The lighter gas, H2, passes through the opening faster than O2, so just after the stopcock is opened, more H2 molecules move to the O2 side than O2 molecules move to the H2 side. (c) After a short time, both the slower-moving O2 molecules and the faster-moving H2 molecules have distributed themselves evenly on both sides of the vessel. By: Rice University Openstax CC BY NC SA

We are often interested in the rate of diffusion, the amount of gas passing through some area per unit time:

rate of diffusion = [latex]\frac{\text{amount of gas passing through an area}}{\text{unit of time}}[/latex]

The diffusion rate depends on several factors: the concentration gradient (the increase or decrease in concentration from one point to another); the amount of surface area available for diffusion; and the distance the gas particles must travel. Note also that the time required for diffusion to occur is inversely proportional to the rate of diffusion, as shown in the rate of diffusion equation.

A process involving movement of gaseous species similar to diffusion is effusion, the escape of gas molecules through a tiny hole such as a pinhole in a balloon into a vacuum (Figure 8.32). Although diffusion and effusion rates both depend on the molar mass of the gas involved, their rates are not equal; however, the ratios of their rates are the same.

This figure contains two cylindrical containers which are oriented horizontally. The first is labeled “Diffusion.” In this container, approximately 25 purple and 25 green circles are shown, evenly distributed throughout the container. “Trails” behind some of the circles indicate motion. In the second container, which is labeled “Effusion,” a boundary layer is evident across the center of the cylindrical container, dividing the cylinder into two halves. A black arrow is drawn pointing through this boundary from left to right. To the left of the boundary, approximately 16 green circles and 20 purple circles are shown again with motion indicated by “trails” behind some of the circles. To the right of the boundary, only 4 purple and 16 green circles are shown.
Figure 8.32 Diffusion involves the unrestricted dispersal of molecules throughout space due to their random motion. When this process is restricted to passage of molecules through very small openings in a physical barrier, the process is called effusion. By: Rice University Openstax CC BY NC SA

If a mixture of gases is placed in a container with porous walls, the gases effuse through the small openings in the walls. The lighter gases pass through the small openings more rapidly (at a higher rate) than the heavier ones (Figure 8.33). In 1832, Thomas Graham studied the rates of effusion of different gases and formulated Graham’s law of effusion: The rate of effusion of a gas is inversely proportional to the square root of the mass of its particles:

Example 8.21
rate of effusion ∝ [latex]\frac{1}{\sqrt{ℳ}}[/latex]

This means that if two gases A and B are at the same temperature and pressure, the ratio of their effusion rates is inversely proportional to the ratio of the square roots of the masses of their particles:

[latex]\frac{\text{rate of effusion of A}}{\text{rate of effusion of B}} = \frac{\sqrt{ℳ_{B}}}{\sqrt{ℳ_{A}}}[/latex]

This figure shows two photos. The first photo shows an inflated orange balloon and an inflated blue balloon. Both balloons are about the same size. The second photo shows the same two balloons, but the orange one is now smaller than the blue one.
Figure 8.33 The left photograph shows two balloons inflated with different gases, helium (orange) and argon (blue).The right-side photograph shows the balloons approximately 12 hours after being filled, at which time the helium balloon has become noticeably more deflated than the argon balloon, due to the greater effusion rate of the lighter helium gas. By: Rice University Openstax CC BY NC SA

EXAMPLE 8.20

Applying Graham’s Law to Rates of Effusion

Calculate the ratio of the rate of effusion of hydrogen to the rate of effusion of oxygen.

Solution

From Graham’s law, we have:

[latex]\frac{\text{rate of effusion of hydrogen}}{\text{rate of effusion of oxygen}} = \frac{\sqrt{32 \cancel{\text{ g mol }^{-1}}}}{\sqrt{2 \cancel{\text{ g mol }^{-1}}}} = \frac{\sqrt{16}}{\sqrt{1}} = \frac{4}{1}[/latex]

Hydrogen effuses four times as rapidly as oxygen.

Check Your Learning

At a particular pressure and temperature, nitrogen gas effuses at the rate of 79 mL/s. Under the same conditions, at what rate will sulfur dioxide effuse?

ANSWER:

52 mL/s

 

 

EXAMPLE 8.21

Effusion Time Calculations

It takes 243 s for 4.46 × 10−5 mol Xe to effuse through a tiny hole. Under the same conditions, how long will it take 4.46 × 10−5 mol Ne to effuse?

Solution

It is important to resist the temptation to use the times directly, and to remember how rate relates to time as well as how it relates to mass. Recall the definition of rate of effusion:

rate of effusion = [latex]\frac{\text{amount of gas transferred}}{\text{time}}[/latex]

 

and combine it with Graham’s law:

 

[latex]\frac{\text { rate of effusion of gas } \mathrm{Xe}}{\text { rate of effusion of gas}\mathrm{Ne}}=\frac{\sqrt{\mathscr{M}_{\mathrm{Ne}}}}{\sqrt{\mathscr{M}_{\mathrm{Xe}}}}[/latex]

 

to get:

[latex]\frac{\frac{\text { amount of } \mathrm{Xe} \text { transfered }}{\text { time for } \mathrm{Xe}}}{\frac{\text { amount of Ne transfered }}{\text { time for } \mathrm{Ne}}}=\frac{\sqrt{\mathscr{M}_{\mathrm{Ne}}}}{\sqrt{\mathscr{M}_{\mathrm{Xe}}}}[/latex]

Noting that amount of A = amount of B, and solving for time for Ne:

[latex]\frac{\frac{\cancel{\text{ amount of } \mathrm{Xe}}}{\text { time for } \mathrm{Xe}}}{\frac{\cancel{\text { amount of Ne }}}{\text { time for } \mathrm{Ne}}} = \frac{\text { time for } \mathrm{Ne}}{\text { time for } \mathrm{Xe}}=\frac{\sqrt{\mathscr{M}_{\mathrm{Ne}}}}{\sqrt{\mathscr{M}_{\mathrm{Xe}}}}=\frac{\sqrt{\mathscr{M}_{\mathrm{Ne}}}}{\sqrt{\mathscr{M}_{\mathrm{Xe}}}}[/latex]

and substitute values:

[latex]\frac{\text { time for } \mathrm{Ne}}{243 \mathrm{s}}=\sqrt{\frac{20.2\cancel{\text{ g mol }}}{131.3\cancel{\text{ g mol }}}} = 0.392[/latex]

Finally, solve for the desired quantity:

time for Ne = 0.392  x  243 s = 95.3 s

Note that this answer is reasonable: Since Ne is lighter than Xe, the effusion rate for Ne will be larger than that for Xe, which means the time of effusion for Ne will be smaller than that for Xe.

Check Your Learning

A party balloon filled with helium deflates to [latex]\frac{2}{3}[/latex] of its original volume in 8.0 hours. How long will it take an identical balloon filled with the same number of moles of air (ℳ = 28.2 g/mol) to deflate to [latex]\frac{1}{2}[/latex] of its original volume?

ANSWER:

32 h

EXAMPLE 8.22

Determining Molar Mass Using Graham’s Law

An unknown gas effuses 1.66 times more rapidly than CO2. What is the molar mass of the unknown gas? Can you make a reasonable guess as to its identity?

Solution

From Graham’s law, we have:

[latex]\frac{\text { rate of effusion of Unknown }}{\text { rate of effusion of } \mathrm{CO}_{2}}=\frac{\sqrt{\mathscr{M}_{\mathrm{CO}_{2}}}}{\sqrt{\mathscr{M}_{Unknown}}}[/latex]

Plug in known data:

[latex]\frac{1.66}{1}=\frac{\sqrt{44.0 \mathrm{g} / \mathrm{mol}}}{\sqrt{\mathscr{M}_{Unknown}}}[/latex]

Solve:

[latex]\mathscr{M}_{U n k n o w n}=\frac{44.0 \mathrm{g} / \mathrm{mol}}{(1.66)^{2}}=16.0 \mathrm{g} / \mathrm{mol}[/latex]

The gas could well be CH4, the only gas with this molar mass.

Check Your Learning

Hydrogen gas effuses through a porous container 8.97-times faster than an unknown gas. Estimate the molar mass of the unknown gas.

ANSWER:

163 g/mol

How Sciences Interconnect

Use of Diffusion for Nuclear Energy Applications: Uranium Enrichment

Gaseous diffusion has been used to produce enriched uranium for use in nuclear power plants and weapons. Naturally occurring uranium contains only 0.72% of 235U, the kind of uranium that is “fissile,” that is, capable of sustaining a nuclear fission chain reaction. Nuclear reactors require fuel that is 2–5% 235U, and nuclear bombs need even higher concentrations. One way to enrich uranium to the desired levels is to take advantage of Graham’s law. In a gaseous diffusion enrichment plant, uranium hexafluoride (UF6, the only uranium compound that is volatile enough to work) is slowly pumped through large cylindrical vessels called diffusers, which contain porous barriers with microscopic openings. The process is one of diffusion because the other side of the barrier is not evacuated. The 235UF6 molecules have a higher average speed and diffuse through the barrier a little faster than the heavier 238UF6 molecules. The gas that has passed through the barrier is slightly enriched in 235UF6 and the residual gas is slightly depleted. The small difference in molecular weights between 235UF6 and 238UF6 only about 0.4% enrichment, is achieved in one diffuser (Figure 8.34). But by connecting many diffusers in a sequence of stages (called a cascade), the desired level of enrichment can be attained.

This figure shows a large cylindrical container oriented horizontally. A narrow tube or pipe which is labeled “porous barrier” runs horizontally through the center of the tube and extends a short distance out from the left and right ends of the cylinder. At the far left, an arrow points right into the tube. This arrow is labele, “Uranium hexafluoride ( U F subscript 6 ).” A line segment connects the label, “High pressure feed tube,” to the tube where it enters the cylinder. In the short region of tube outside the cylinder, 5 small, purple circles and 4 small, green circles are present. Inside the cylinder, an arrow points right through the tube which contains many evenly distributed, purple circles and a handful of green circles which decrease in quantity moving left to right through the cylinder. Curved arrows extend from the inner area of the tube into the outer region of the cylinder. Three of these arrows point into the area above the tube and three point into the area below. Two line segments extend from the label, “Higher speed superscript 235 U F subscript 6 diffuses through barrier faster than superscript 238 U F subscript 6,” to two green circles in the space above the tube. In the short section of tubing just outside the cylinder, 8 small, purple circles are present. An arrow labeled, “Depleted superscript 238 U F subscript 6,” points right extending from the end of this tube. The larger space outside the tube contains approximately 100 evenly distributed small green circles and only 5 purple circles. Eight of the purple circles appear at the left end of the cylinder. A tube exits the lower right end of the cylinder. It has 5 green circles followed by a right pointing arrow and the label, “Enriched superscript 235 U F subscript 6.”
Figure 8.34 In a diffuser, gaseous UF6 is pumped through a porous barrier, which partially separates 235UF6 from 238UF6 The UF6 must pass through many large diffuser units to achieve sufficient enrichment in 235U. By: Rice University Openstax CC BY NC SA

The large scale separation of gaseous 235UF6 from 238UF6 was first done during the World War II, at the atomic energy installation in Oak Ridge, Tennessee, as part of the Manhattan Project (the development of the first atomic bomb). Although the theory is simple, this required surmounting many daunting technical challenges to

make it work in practice. The barrier must have tiny, uniform holes (about 10–6 cm in diameter) and be porous enough to produce high flow rates. All materials (the barrier, tubing, surface coatings, lubricants, and gaskets) need to be able to contain, but not react with, the highly reactive and corrosive UF6.Because gaseous diffusion plants require very large amounts of energy (to compress the gas to the high pressures required and drive it through the diffuser cascade, to remove the heat produced during compression, and so on), it is now being replaced by gas centrifuge technology, which requires far less energy. A current hot political issue is how to deny this technology to Iran, to prevent it from producing enough enriched uranium for them to use to make nuclear weapons.

License

Icon for the Creative Commons Attribution 4.0 International License

Chemistry 110 Copyright © by OpenStax is licensed under a Creative Commons Attribution 4.0 International License, except where otherwise noted.

Share This Book